| Morso
NXLEH Series: Automatic Guillotine for Beaded Face Frames |
|
|
Click
here to enlarge
|
The machine
features a heavy-duty steel frame with cast iron tabletop.
The vertical travel of the cutting head, which is also made
of cast-iron, can be adjusted in two positions depending
on workpiece thickness, assuring fast and efficient operation.
When set to the lower setting, the complete cutting cycle
(trim cut and finish cut) is completed in 1.5 seconds!!!
The machine is equipped with two cast-iron table extension
leaves, which are bolted to the main table. Steel pins provide
accurate alignment. Mounted on top of the table extension
leaves are anodized aluminum fence rails which are used
in conjunction with flip-stops to position multiple cuts
along a stile or rail. These fence rails are also bolted
and pinned to the table leaves.
|
A
center stop assembly in the middle of the machine table
is used to position the rails for cope cuts. The solid aluminum
center stop bar slides in and out and is locked in place
with a thumbscrew. Interchangeable nylon center fittings
with fine adjustment screws are installed in the center
stop bar and are available in different widths, depending
on the nose knife used.
A nylon chip breaker is installed in the machine table.
The chip breaker protects the cutting edges of the knives
and also prevents any tear-out on the back of the workpiece.
Heavy aluminum blocks with two setscrews act as “cock-bead"
stops. These blocks are mounted on steel guide rails next
to the side knives. Once set, the stops limit the forward
travel of the cutting head and assure accurate notching
depths. Because the stops use the beaded edge of the moulding
as reference point, this design completely avoids to problems
associated with systems using the opposite moulding edge
instead.
|
 |
Center Fence
Details |
|
Setting for approx. 4" wide moulding
click
here to enlarge
|
|
|
The main difference between the NXLEH and the NLEH model
is the moveable center fence assembly on the NXLEH.
Two 5-foot long fence rails are mounted along the back edge
of the table extensions (along the front edge on the NLEH).
The center fence assembly can be moved in and out, allowing
moulding up to 8” in width to be placed between the
center fence and the nose knife.
The center stop, which is fastened to the machine table
on the NLEH models, is also part of the moveable center
fence assembly on the NXLEH.
Four additional grooves are machined into the cast iron
table, the angled outer grooves holding locking fittings
to lock the fence assembly into place. The straight grooves
in the center contain moving steel channels, which guide
the center assembly to assure parallel alignment to the
nose knife and extension fences.
|
»
Back to Top |
|
Knives |
|
The nose knives feature a machined v-groove in the back
to guarantee accurate alignment on the cutting head. In
addition, two counter sunk hex-head screws are used to mount
the nose knives to the tip of the cutting head.
The side knives are bolted to the head with heavy-duty
machine bolts. Slots in the knives allow for lateral adjustment
depending on the width of the nose knife.
The side knives are designed to be compatible with both
the small and large cutting heads for the NFL and NLEH series.
All MORSO knives are manufactured with custom-made Austrian
steel and are hardened to Rockwell 64. No other manufacturer
of miter cutting and notching equipment offers knives harder
than Rockwell 58!
|
|
| |
»
Back to Top |
|
Notching
Operation (stiles) |
|
Operation on NFL model
click
here to enlarge
|
|
|
Upon adjusting the cock-bead stops to set the notching
depth, the moulding is placed on the machine table and
one end is rested against a flip-stop. Two safety buttons,
located at the left and right hand side of the machine
table, are pressed simultaneously to start the cutting
cycle:
- Hydraulic clamps secure the moulding against the
fence rails
- The cutting head advances toward the operator
- Upon touching the moulding edge, sensors trigger
two consecutive downward strokes of the cutting head
(trim cut and finish cut)
- The cutting head returns to its home position and
the clamps release the material
When set to the lower setting, the complete
cutting cycle (trim cut and finish cut) is completed in
1.5 seconds and the resulting cuts are smooth and free
of tear-out.
|
»
Back to Top |
|
Coping operation
(rails) |
|
Upon adjusting the setscrews in the nylon center fitting,
the stop is moved toward the cutting head and locked in
place. The rail is placed on the table and pushed against
the stop. Both safety buttons are activated and the 45-degree
corner is cut. The moulding is then flipped end-for-end
and the process is repeated.
|
click
here to enlarge |
| |
»
Back to Top |
|
Cutting Head
Details: |
|
To increase the range of applications, we offer matched
smaller cutting heads with each machine. These heads
are fitted at the MORSO factory and can be replaced
in only minutes. The side knives fit on both heads;
only the nose knives differ in design.
We highly recommend the purchase of the smaller
head to produce haunch joints in window grills, cabinet
door mullions, etc. The cast-iron head actually costs
less than a second pair of side knives!
|
|
|
Technical Specifications
|
| |
|
|
| |
Pump
motor: |
220
volts, single phase, 60 Hz - 1,1 KW, 10 Amp. |
| |
Fluid
turnover: |
1.85
gal. (7 liters) per minute |
| |
Operating
pressure: |
1,200 psi (80 bar) |
| |
Hydraulic
fluid type: |
Shell
TELLUS S32 or equivalent |
| |
Max.
moulding width: |
8"
(203mm)
|
| |
Max.
moulding thickness: |
5 1/2" (140mm) |
| |
Nose
knife capacity: |
1/2"
- 1" with standard cutting head
1/4" , 5/16", 3/8" with smaller cutting head
|
| |
Extension
tables: |
Heavy
cast iron, smooth machined surface, 30 3/4" long, one
left and one right hand side |
| |
Fence
rails: |
Silver
anodized aluminum, 59 1/2" total length, one left and
one right hand side |
| |
Flip-stops:
|
Aluminum,
with locking lever, four with short arm, two with long arm
(arms are reversible - can be used on left and right hand
side) |
| |
Table
height: |
33"
(floor to table surface) |
| |
Width
incl. fence rails: |
118" |
| |
Depth
incl. scrap chute: |
24" |
| |
Machine
weight: |
320
lbs. |
| |
|
|
|
Standard Features:
|
|
MORSO NXLEH series electro - hydraulic guillotine
for beaded face-frames include:
- safety guard
-
-
four short-arm flip-stops and
two long-arm flip-stops
-
left and right hand side cast
iron table extensions
-
eft and right hand side aluminum
fence rails
-
one set of original MORSO side
knives, factory ground and honed
-
one ¾" wide nose knife
and one 1" wide nose knife, factory ground
and honed
- detailed instructions incl. parts diagrams
|
|
|
Recommended
Options : |
|
|
Factory-fitted smaller cutting head for 1/4”, 5/16”,
3/8” nose knives, used for half-lap and cope joints
on window grills and muntin bars. Made for easy interchange
with the standard cutting head, these smaller heads differ
from the standard only in the fact that the two sides actually
come to a point at the tip, while the larger heads have
an approx.. 1/4” flat area at the tip.
Item #
N
7141
Price:
$ 343.00
Click
here for detailed description.
|
»
Back to Top |
|
GlideStop
fence stop system for manual and electro-hydraulic MORSO
notching machines, complete with 2 x 5 foot long fence rails,
20 x adjustable index stops, 1x GlideStop with extended
contact bolts, 1 x left hand and 1 x right hand tape scale
(inches), 4 x mounting brackets and instructions
Easy retrofit installation, adds pre-set stops and accurate
“inch” scale to notching machines.
Item #
DGS
1000 Price:
$ 584.00
Click
here for detailed description and to view demo.
|
|
Warranty : |
|
Mechanical parts are warranted for twelve months.
Complete MORSO warranty terms apply.
|
»
Back to Top |
|
Machine Price
: $18,945.00 |
| |
|
|
|
|
